lite-on dcc release lite-on technology corp. / optoelectronics no.90,chien 1 road, chung ho, new taipei city 23585, taiwan, r.o.c. tel: 886-2-2222-6181 fax: 886-2-2221-1948 / 886-2-2221-0660 http://www.liteon.com/opto through hole lamp product data sheetLTL-1CHG-012A spec no.: ds-20-96-0163effective date: 03/31/2000revision: - bns-od-fc001/a4 bns-od-fc001/a4 bns-od-fc001/a4 bns-od-fc001/a4
l i t e - o n e l e c t r o n i c s , i n c . p r o p e r t y o f l i t e - o n o n l y features * low power consumption. * high efficiency. * versatile mounting on p.c. board or panel. * i.c. compatible/low current requirement. * 3.1 mm diameter package. package dimensions part no. lens source color ltl - 1chg - 012a green diffused green notes: 1. all dimensions are in millimeters (inches). 2. tolerance is 0.25mm(.010") unless otherwise noted. 3. protruded resin under flange is 1.0mm(.04") max. 4. lead spacing is measured where the leads emerge from the package. 5. spec ifications are subject to change without notice. part no. : ltl - 1chg - 012a page : 1 of 5 bns - od - c131/a4
l i t e - o n e l e c t r o n i c s , i n c . p r o p e r t y o f l i t e - o n o n l y absolute maximum ratings at t a =25 parameter maximum rating unit power dissipation 100 mw peak forward current (1/10 duty cycle, 0.1ms pulse width) 120 ma continuous forward current 30 ma derating linear from 50 0.4 ma/ reverse voltage 5 v operating temperature range - 55 to + 100 storage temperature range - 55 to + 100 lead soldering temperature [1.6mm(.063") from body] 260 for 5 seconds part no. : ltl - 1chg - 012a page : 2 of 5 bns - od - c131/a4
l i t e - o n e l e c t r o n i c s , i n c . p r o p e r t y o f l i t e - o n o n l y electrical optical characteristics at t a =25 parameter symbol min. typ. max. unit test condition luminous intensity i v 3.7 12.6 mcd i f = 10ma note 1,4 viewing angle 2 1/2 60 deg note 2 (fig.6) peak emission wavelength p 565 nm measurement @peak (fig.1) dominant wavelength d 569 nm note 3 spectral line half - width ? 30 nm forward voltage v f 2.1 2.6 v i f = 20ma reverse current i r 100 a v r = 5v capacitance c 35 pf v f = 0 , f = 1mhz note: 1. luminous intensity is measured with a light sensor and filter combination that approximates the cie (commission international de l'eclairage) eye - response curve. 2. 1/2 is the off - axis angle at which the luminous intensity is half the axial luminous intensity. 3. the dominant wavelength, d is derived from the cie chromaticity diagram and represents the single wavelength which defines the color of the device. 4. the iv guarantee should be added 15%. part no. : ltl - 1chg - 012a page : 3 of 5 bns - od - c131/a4
l i t e - o n e l e c t r o n i c s , i n c . p r o p e r t y o f l i t e - o n o n l y typical electrical / optical characteristics curves (25 ambient temperature unless otherwise noted) part no. : ltl - 1chg - 012a page : 4 of 5 bns - od - c131/a4
l i t e - o n e l e c t r o n i c s , i n c . p r o p e r t y o f l i t e - o n o n l y features * compatible with radial lead automatic insertion equipment. * most radial lead plasti c lead lamps available packaged in tape and folding. * 5mm (0.197") formed lead and 2.54mm (0.1") straight lead spacing available. * folding packaging simplifies handling and testing. package dimensions specification it em symbol minimum maximum mm inch mm inch tape feed hole diameter d 3.8 0.149 4.2 0.165 component lead pitch f 2.3 0.091 3.0 0.118 front to rear deflection h -- -- 2.0 0.078 feed hole to bottom of component h1 21.5 0.846 22.5 0.886 feed hole to overall component height h2 26.4 1.039 28.0 1.102 lead length after component height l w0 11.0 0.433 feed hole pitch p 12.4 0.488 13.0 0.511 lead loca tion p1 4.4 0.173 5.8 0.228 center of component location p2 5.05 0.198 7.65 0.301 total tape thickness t -- -- 0.90 0.035 feed hole location w0 8.5 0.334 9.75 0.384 adhesive tape width w1 12.5 0.492 13.5 0.531 adhesive tape position w2 0 0 3 .0 0.118 tape width w3 17.5 0.689 19.0 0.748 part no. : ltl - 1chg - 012a page : 5 of 5 bns - od - c131/a4
|
